Standard Features
  • Built in accordance with A.S.M.E. Miniature Boiler Code
  • A.S.M.E. CSD-1 Compliant
  • UL Listed and labeled under UL 834
  • Dual Pressure Controls (UL 353)
  • High Pressure Safety Reset. (UL 353)
  • Low Level Cut-Off (LLCO) (UL 353)
  • 100 psi Safety Relief Valve (A.S.M.E. Section I - V Stamp)
Recommended Options (Non-Standard)
  • Spare Parts Package
  • Motorized Automatic Flush and Drain (MAFD)
Unit of Measure

Specifications

Brands

N/A Electro-Steam™

Electrical Power Rating

N/A 10 kW
Power Supply Voltage1 N/A 208 VAC230 VAC380 VAC415 VAC440 VAC480 VAC600 VAC
Phase2 N/A 3

Frequency

N/A 50 Hz60 Hz

Boiler Horse Power

N/A 1.00 bhp
Steam Capacity3 N/A 34.50 lb/hr15.65 kg/h

Water Consumption

N/A 4.13 gal/h15.65 L/h

Gross British Thermal Units (BTU) Output

N/A 33475 Btu/hr

Maximum Boiler Pressure

N/A 100 psi

Operating Pressure (Factory Set at 80 Pound per Square Inch (psi))

N/A 0 to 80 psi

Maximum Boiler Capacity

N/A 2.90 gal

Boiler Fill Capacity

N/A 1.90 gal
Boiler Material4 N/A Carbon Steel

Cabinet Material

N/A 304 Stainless Steel

Plumbing Material

N/A Brass (Schedule 40) Carbon Steel (Schedule 40)

Industry Standards

N/A American Society of Mechanical Engineers (ASME) - Boiler and Pressure Vessel Code American Society of Mechanical Engineers (ASME) - CSD-1 Underwriters Laboratories (UL) Canadian Underwriters Laboratories (cUL)

Amperage

Amperage at 208 VAC (3Ø Phase)

N/A 27.80 A

Amperage at 240 VAC (3Ø Phase)

N/A 26.20 A

Amperage at 380 VAC (3Ø Phase)

N/A 15.20 A

Amperage at 415 VAC (3Ø Phase)

N/A 13.90 A

Amperage at 440 VAC (3Ø Phase)

N/A 13.10 A

Amperage at 480 VAC (3Ø Phase)

N/A 12.00 A

Amperage at 600 VAC (3Ø Phase)

N/A 9.60 A

Dimensions

Length

N/A 23 in

Width (No Options Included)

N/A 27 in

Width (Motorized Automatic Flush and Drain (MAFD) Option Included)

N/A 30 in

Height

N/A 18 in

Minimum Clearance

Total Length

N/A 35 in

Total Width

N/A 45 in

Total Height

N/A 22 in

Plumbing Connection Sizes

Water Inlet

N/A 3/8" National Pipe Thread NPT (Female) - Y-Strainer, Brass

Steam Outlet

N/A 1/2" National Pipe Thread (NPT) (Female) - Ball Valve, Brass

Safety Valve

N/A 3/4" National Pipe Thread (NPT) (Female) - Safety Valve, Brass

Drain

N/A 1" National Pipe Thread (NPT) (Female) - Ball Valve, Brass

Additional Drain (Motorized Automatic Flush and Drain (MAFD) Option Included)

N/A 1" National Pipe Thread (NPT) (Female) - Motorized Valve, Brass

Options

Spare Parts Package Includes

N/A
  • 18-Month Warranty (12-Month Standard)
  • (1) Electric Heaters and (1) Heater Gaskets
  • (2) Sight Glass Tubes and (4) Washers
  • (1) Pressure Control
  • (1) Contactor

Motorized Automatic Flush and Drain (MAFD)

N/A During Start-Up before steam pressure is accumulated, the Motorized Automatic Flush and Drain option cycles fresh water through the boiler for 0-300 seconds (Factory set for 180 seconds or three (3) minutes). As old water is drained out, fresh water will be cycled in. This drain valve will not open if boiler pressure exceeds 5 psi, and the electric heaters are locked out during flush cycle.
Manual Low Water Reset5 N/A Manual Low Water Reset trips if the electric heaters shut-off because of a low water condition. Reset must be manually pressed to resume steam production.

Water Feed Booster Pump

N/A Supplied standard on any steam generator with an operating pressure higher than 15 psi. The Water Feed Booster Pump increases your incoming water pressure to overcome the operating pressure of the steam generator. The Pump requires a 5-150 psi water supply with a minimum flow rate of 2 gpm.
  • 1 Each Electro-Steam™ electric steam generator requires two (2) power supplies: One (1) customer specific primary high voltage supply for the heaters and one (1) secondary 120 VAC 1Ø, 50/60 Hz supply for the Controls.
  • 2 3.33-6.65 kW steam generators are only available in Single Phase (1Ø); 8.33-10 kW steam generators come in Three Phase (3Ø), but are also available in Single Phase (1Ø).
  • 3 Calculations are based off of a 212 ºF boiler feed-water temperature. Boiler feed-water temperatures that range between 60 ºF and 140 ºF, are approximately 80% to 90% of the calculated values shown. Boiler feed-water must not exceed 140 ºF.
  • 4 Wetted Surfaces.
  • 5 A Manual Low Water Reset Button is supplied standard with every steam generator, but it is disabled. If this Reset Button is required as per your local boiler codes, simply plug the two attached wires into the PC-Board terminals labeled "Reset".